TainetVenus2816 (SDZ1)

Description

This resource allows to connect a TAINET Venus 2816.

Release notes

Resource configuration interface

Tainet Venus 2816 : Resource configuration parameters

• Line selection
  • Line: Indicate the line to configure.
• Line configuration:
  • Rx Gain: RX(reception) Gain Controls for each line
  • Tx Gain: TX(transmission) Gain Controls for each line
• SIP Server Features (only applicable for line 1)
  • T38: Indicate if T38 must be enabled
  • SIP Server: Indicate here the IP address where to register. By default, it will be the IP address of SOP 1.
  • Call Feature
    • Max Flash Hook Time (msec): This option specifies the maximum flash hook detection period in msec.
    • Min Flash Hook Time (msec): This option specifies the minimum flash hook detection period in msec.
    • Play Ring Back Tone: This option specifies the ring back response type.
    • Call Hold: This option specifies the hold type.
    • Call Waiting: This option enable/disable the call waiting.
    • Call Transfer: This option enable/disable the call transfer.
    • Call Redial: This option enable/disable the call redial.
    • Invite with SDP: When enable this feature, Invite session will involve SDP body. Otherwise, the SDP body will be sent in ACK message.
    • Caller ID Type: This item specifies the caller ID type: FSK, ETSI, DTMF or disable.
    • Prack: Enable this feature, IAD will ask the caller or caller to use PRACK and this feature is required. Details please refer RFC 3262.
    • Max Concurrent Call: This option specifies the maximum concurrent call.
    • Phonebook fall back: This option enable/disable the phonebook fall back.
  • Area Code: This menu is for selecting a pre-programmed POTS specification for some specific countries.
  • DHCP Client: This option enable/disable the dhcp client.
  • Preferences
    • RTP Port Base: The UDP port starting number for Real-time Transport Protocol.
    • RFC-2833: It enables the RTP Payload to carry dual-tone multi-frequency (DTMF) signaling, other tone signals and telephony events in RTP packets.
    • Preferred Codec: Preferred codec for all calls. (The actual codec used in a call still depends on the outcome of the codec negotiation protocol.) Select one of the following: G711u, G711a, or G729a.
    • Use Pref Codec Only: To use only the preferred codec for all calls, select yes. (The call fails if the far end does not support this codec.) Otherwise, select no. Default setting: no
    • G711 Ptime(ms): This item specifies the preferred ptime for G711 (10/20/30ms).
    • G729 Ptime(ms): This item specifies the preferred ptime for G729 (10/20/30/40/50/60ms).
    • Voice Activity Detector: If one side of a connection is not speaking, the system will sending voice transmission.
    • Echo Canceller: Prevents poor telecommunication quality caused by echo interface.
    • RTCP: If this item is enabled, the system will send RTCP package front of RTP package.
    • RTP Filter: Enable or disable RTP filter function.
• Phone Features (only applicable for line 1)
  • Timeout settings
    • Ringing (sec): Amount of ringing timeout in seconds.
    • Inter-digit (sec): Amount of timeout in seconds inter each digit dialing.
    • Invite Expire (sec): Amount of Invite session timeout in seconds.
    • Dial tone (sec): Amount of dial tone timeout in seconds.
    • Busy tone (sec): Amount of busy tone timeout in seconds.
    • Reorder tone (sec): Amount of reorder tone timeout in seconds.
    • Stutter tone (sec): Amount of stutter tone timeout in seconds.
  • Long Loop: The “Long Loop” enables the longer distance service of voice higher 8Km than 3Km.
  • Dialplan: Provides the dialplan matching rules used to decide when to send the INVITE will dialling out. The symbol "x" matches a digit between 0 and 9. A range can be defined with the brackets "[" and "]". A Subrange is defined with "-". The symbol "." indicates that the previous pattern can be repeated several times, including zero. Several pattern can be separated by the symbol "|". For example "[0-9*].|*xxx|**xx".

First time manual Setup procedure

Connection to the Tainet Venus

• Connect the Tainet to the network via the Wan port
• Connect via telnet to the Tainet Venus, if it's not work use the Serial cable connection and Enable DHCP Client procedure (you may need to repeat this step after the switch of the firmware and the restore of default parameters)
• The default login is "user" and password is blank.
• Switch the firmware,

• Restore Default parameters,

• Load the initial configuration,

• Restart the device,

Serial cable connection

Connection

The console interface designed on VENUS Series is a female, DCE type RS-232 port. A straight DB-9 to DB-9 or DB-9 to DB-25 serial cable can be used to connect VENUS Series directly to a PC’s serial port for terminal operation.

Speed and Data format: 115200bps, none parity, 8 data bits, 1 stop bit, and no flow control.

mhe@mhe-laptop ~ $ screen /dev/ttyS0 115200,cs8,-parenb,-cstopb,-hupcl

Where,

• /dev/ttyS0: Linux serial port /dev/ttySX
• 115200 baud
• 8 data bits
• no parity
• one stop bit
• VT100 terminal emulation

Enable DHCP Client

Limitations

For the provisioning, if you use your own DHCP server you've two possibilities:

• Add a static lease for each Tainet Venus with the option bootfile-name set to {mac}.ini (Replace {mac} by the device mac address, for example: 0090bb1740a6.ini)
• Skip the option bootfile-name for Tainet Venus devices.

Dependencies

The following module is required: Tainet Venus Support module

Advanced Troubleshoot

• Tainet_Venus_SIP_Manual.pdf: TainetDoc