 |
SNOM300 (SDO1)
Description
This resource allows to connect a SNOM 300 IP Phone.
Release notes
Version 3.13.1 - Early deployment
- Bugfix: The SDP in the answer could contain more than one codec (M11793)
- Dependency:
- Snom Phone Support module v1.11.0+
- Feature: Configurable voicemail service extension. (M7747)
- Dependency:
- Snom Phone Support module v1.11.0+
- Feature: Added support for Connected Line Update (M5654)
- Improvement: Increased interval for firmware update check (M5125)
- Dependency:
- Snom Phone Support module v1.11.0+
- Feature: Allow the possibility to deactivate auto update (M5125)
- Dependency:
- Snom Phone Support module v1.11.0+
- Improvement: Aligned all SNOM 3x0 resources.
- Dependency:
- Snom Phone Support module v1.11.0+
- Improvement: Active-active was working only partially (M5102)
- Dependency:
- Snom Phone Support module v1.11.0+
- Bugfix: Disabled SRTP (Backport from v3.13.0)
- Dependency:
- Snom Phone Support module v1.11.0+
- Bugfix: Vlan ID parameter never accepted since new firmware.
- Dependency:
- Snom Phone Support module v1.11.0+
- Feature: Disable audio notification for the auto-answer (M4083)
- Dependency:
- Snom Phone Support module v1.11.0+
- Feature: Expiry time now configurable.
- Feature: Support of active-active environments.
- Improvement: Duplicate MAC address is now detected.
- Dependency:
- Snom Phone Support module v1.11.0+
- Feature: Added active-active support
- Deprecated: Significant improvements have been done in a higher version
- Dependency:
- SNOM Phone Support module v1.9+
- Feature added: integrate Directory service
- Dependency:
- Snom Phone Support module v1.9+
- Feature added: integrate Directory service
- Dependency:
- Snom Phone Support module v1.9+
- Bug fix: Remove "HTTP Password not set" on display of phone
- Bug fix: When speeddials are cleared on SMP, this is not cleared in the phone.
- Dependency:
- Snom Phone Support module v1.7+
- Buf fix: Cannot change language with new Snom firmware v7+
- Dependency:
- Snom Phone Support module v1.7+
- Will now display missed calls by default
- Modified configuration file, required for firmware 7.1.30+
- "Return to/stay in idle even if offhook" option added
- action URL added
- TimeZone setting added
- Bugfix: Disabled SRTP (Backport from v3.13.0)
- action URL added
- automatic firmware update added
- Feature: Initial release
Resource configuration interface
GUI unavailable.
Resource configuration parameters
This resource allows an administrator to configure a SNOM 300 IP Phone.- Line: A line corresponds to a specific SIP identity. This means that your SNOM300 IP phone can have several identities and each resource corresponds with a particular identity which is also called 'Line'. Select whether you wish to configure the resource on line 1 or line 2 of the SNOM300 phone. Please note that you have to configure the resource with the line 1 before you can create a new resource with the same mac address and line2.
- SIP can reinvite: if this option is set to 'yes', you will instruct the media flow, i.e. the actual voice packets, to be send directly to the destination phone without transiting through the Escaux UCS server. Activating this option can be interesting in large deployments but can result in compatibility problems when establishing a voice communication between IP phones of a different brand. The default value is 'no'.
- Auto-answer type: this option allows you to activate the auto-answer mode. You can define whether the calls should be sent either to the handset, headset or phone speaker. "Locked" means that the setting cannot be changed through the phone menu.
- VLAN and DSCP configuration:
- DSCP
-
Please note that these settings are only applied to the phone if you have selected Line 1
- Diffserv setting for Voice Media (RTP) : Diffserv classification for phone voice outbound IP traffic (see also ModuleDoc30)
- Diffserv setting for Voice Signaling (SIP) : Diffserv classification for phone signaling (SIP, ...) outbound IP traffic (see also ModuleDoc30)
-
- VLAN
-
Important note : The following network parameters can break the connexion between the phone and the Escaux UCS. If incorrect values are indicated, a factory reset of the phone might be needed.
- Voice VLAN id (1 -> 4094) : 802.1q voice VLAN id
- Voice VLAN priority (0 -> 7) : 802.1p voice VLAN priority
-
- DSCP
- Additional settings:
- Display missed calls : Set to "no" to hide missed calls.
- Call waiting : Set to "yes" to allow incoming calls when already in conversation.
- Web access security : Leave blank to allow default configuration. Do not configure this in combination with net.Console.
- Language : Choose the phone and web interface language.
- Tone scheme : The type of ringtones that will be generated by the phone.
- Phone display : This configured what will be displayed on screen when the phone is idle.
- Function keys :
- Key event : Set this to leave it at the factory default.
- Speeddial : Fill in the extension as you would dial it on the phone.
- BLF+Speeddial : Same as speeddial but only for internal extensions. The extension specified will be supervised. The led next to the button will light up when the extension is busy.
- Action URL : When this value is selected, you can specify a url that the phone can request. See the application note below for more information.
- RTP Port range : This configures the RTP port range the phone will use.
- Time zone : Configures the timezone.
- Return to idle even if offhook : When set to "yes" the phone will return to idle when the call has ended but the handset is not yet on the hook (and thus allowing new incoming calls).
- Expiry The proposed expiry time of the registration in minutes. Upon expiration of the registration, the phone will send a fresh re-registration request.
Copyright © Escaux SA