ThomsonST2022 (SDT1)

Description

This resource allows to connect a Thomson ST2022 IP Phone.

Release notes

Show release notes
Version 1.2.1 - Early deployment
  • Bugfix: SIP Peer were created on all the SOPs of the cluster (M20050)
  • Dependency:
    • System Base >= 1.3.0
    • Thomson Phone Support module >= 1.5.1

Version 1.2.0 - Early deployment
  • Bugfix: Old configuration files were not correctly deleted after an apply changes (M8764)
  • Dependency:
    • System Base >= 1.3.0
    • Thomson Phone Support module >= 1.5.1

Version 1.1.1 - Early deployment
  • Bugfix: Configuration was not generated when a lot of phones are used in the cluster. (M8666)
  • Limitation: When no Display name is received when initiating a call the subsequent connected line update are ignored (M8935)
  • Dependency:
    • System Base >= 1.3.0
    • Thomson Phone Support module >= 1.4.0

Version 1.1.0 - Early deployment
  • Feature: Using firmware v3.66 (M8024)
  • Feature: Allow language to be set from global user configuration (M8280)
  • Feature: Registration time was not configurable (M8286)
  • Feature: Support Active/Active (M8303)
  • Bugfix: The extension or the name was not shown correctly on the phone screen (M8282)
  • Bugfix: Changes were not applied when doing an apply phone changes (M8276)
  • Bugfix: Accented characters were not displayed correctly (M8283)
  • Dependency:
    • System Base >= 1.3.0
    • Thomson Phone Support module >= 1.4.0

Version 1.0.0 - General deployment
  • Improvement: Firmware 3.56

Version 0.0 - Deprecated
  • Firmware 3.56

Resource configuration interface

GUI unavailable.

Resource configuration parameters

  • Displayed owner info: Display information about the phone owner. This can be:
    • Extension: show the extension pointing towards this phone.
    • Name: show the extension owner's name on the phone.
    • Name and Extension: shows both name and extension.

  • Auto-Answer: Ability to auto-answer a call after a configurable period of time.

  • Off hook dialing configuration: Ability to dial automatically a number when the phone goes off-hook.
    • Off hook dialing mode: Enabled or Disabled
    • Dialed number: number which will be automatically dialed.

  • Feature configuration:
    • Hide missed calls: Suppress missed calls notifications.
    • Beep when pressing a key: Enable or disable the tone generated when a user press on a key.
    • Allow reboot by user: Allow/disallow the user to reboot the phone through the user menu.
    • Allow phone lock by user: Allow/disallow the user to lock his phone through the user menu.
    • Allow Do Not Disturb key: Allow/disallow the user to use the 'Do Not Disturb' option. (All calls to the phone are reported as busy when the Do Not Disturb Option is activated)
    • Allow Auto Answer config by user: Allow/disallow the user to activate or deactivate the auto-answer option through the user menu.
    • Allow Anonymous Call Blocking: Allow/disallow the user to block anonymous calls through the user menu.
    • Allow Call Waiting config. by user: Allow/disallow the user to activate/deactivate the call waiting (possibility to receive several calls) through the user menu.
    • Allow Call Forwarding config by user: Allow/disallow the user to configure a call forwarding on the phone through the user menu.
    • Allow Call Blocking config by user: Allow/disallow the user to block certain incoming calls through the user menu.
    • Allow Transfer to vmail soft key: Activate/deactivate the 'Transfer to voicemail' key.

  • Localization:
    • Phone user interface language: Allow to configure the language the phone is using to display messages.
    • Ringtones: Allow to configure localized ringtones.
    • Day light saving: Allow to enable or disable dailight saving.
    • Timezone: Allow to configure the timezone.
    • Ringtone: Allow to configure the type of ringtone
    • Inter-digit timeout: Allow to configure a timeout while waiting for the next digit.

  • Dial plan:
    • Regular: Enable to automatically compose a number when a certain rule is matched.
    • Emergency: Leave empty. For futur usage. 

The dial plan can be configured with a "|" separated value of the following characters :

   * Digit: A Digit from "0" to "9".
   * Timer: The symbol "T" matching a timer expiry.
   * Wildcard: The symbol "x" which matches any digit ("0" to "9").
   * Position: A period (".") which matches an arbitrary number, including zero, of occurrences of the preceding   construct.
   * Range: One or more DTMF symbols enclosed between square brackets("[" and "]").
   *Subrange: Two digits separated by hyphen ("-") which matches any digit between and including the two.
      *The subrange construct can only be used inside a range construct, i.e., between "[" and "]".
   * Or: Add more dial rule with "|".

The following example illustrates the above.

   * "xxxx": If dial number exactly matches 4 digits, then we send it.
   * "100x": If dial number exactly matches 4 digits and the first 3 digits are "100", then we send it.
   * "[1-3]xxx": If dial number exactly matches 4 digits and the first digit is "1", "2" or "3", then we send.
   * "xxxxT": If dial number exactly matches 4 digits then we send it after the inter-digit timeout.
   * "xxxx.T": If dial number matches at least 4 digits then we send all digits after the inter-digit timeout.
   * "100x.T": If the first 3 digits of dial number are "100", then we send all digits after the inter-digit timeout.

  • VLAN and DSCP
    • ALERT! Important note : These network parameters can break the connexion between the phone and the Escaux UCS. If incorrect values are indicated, a factory reset of the phone might be needed.
    • Diffserv setting for Voice RTP : Diffserv classification for phone voice outbound IP traffic (see also ModuleDoc30)
    • Diffserv setting for Voice Signaling : Diffserv classification for phone signaling (SIP, ...) outbound IP traffic (see also ModuleDoc30)
    • Voice VLAN id (1 -> 4094) : 802.1q voice VLAN id
    • Data VLAN id (1 -> 4094) : 802.1q data VLAN id (VLAN of the PC connected to the Phone switch)

  • SIP/RTP specific parameters
    • RFC2833 RTP payload type : Defines the type of payload used for the DTMF with RFC2833
    • Registration refresh period (seconds): : Number of seconds before the phone tries to register again. Setting it at its smallest value ensure that the phone will be reachable as soon as possible when the primary SOP is down and the secondary SOP is configured.
Copyright © Escaux SA